Pro Tips: What Does “Anodized” Mean for a Fly Reel?


Written by: Phil Monahan

Anodizing has a big effect on a reel’s durability and color.
Photos via orvis.com

Whenever you see advertising copy for a fly reel, it usually mentions that the metal is anodized. (For instance, the description might say that the reel is made from “anodized 6061 T6 aluminum.”) The copy might even note that there’s a special type of anodizing involved. If you’re not really sure what these terms mean, here’s a brief primer.

Anodizing is a chemical process that creates a coating on the surface of a metal (usually aluminum), which makes the metal more durable and resistant to scratches and dings. Anodizing also increases corrosion resistance and makes the metal easier to dye. Reel manufacturers use aluminum because it is so light, but it’s also quite soft. Without anodizing, an aluminum reel would not be very durable.

The most common method of anodizing involves dipping the aluminum in sulfuric acid and then running electrical current through the acid. This causes aluminum oxide to form on the surface. Unlike iron oxide—which we call “rust”—the aluminum oxide does not flake off and is, in fact considerably harder than bare aluminum. Because this film of aluminum oxide is somewhat porous, it can be dyed or painted various colors.

Fly reels generally come in Type II, although some–such as the new made-in-the USA Mirage Reels–feature Type III anodizing, which is also known as “hard anodizing.” The “Type” describes the thickness and consequent hardness of the coating. Type II anodizing creates a coating of less than .001 inches, while Type III describes anything between .001 inches and .004 inches. Manufacturers claim that Type III anodizing “penetrates” the metal, as well as coating it, but all anodizing methods penetrate to a certain degree.

“If Type III is thicker and harder,” you may ask, “why not make all reels with Type III anodizing?” First of all, the hard-anodizing process is much more complicated, involving colder temperatures, more electrical current, and an electrolyte solution. This is more expensive, so it adds cost to the reel. Hard anodizing is also considerably less porous, so it doesn’t accept dye as well. This is why Type III reels such as the Mirage are available in black or dark gray only.


Type III anodizing does not allow manufacturers to make colorful reels, but they are extremely durable.

It’s important to note, however, that not all anodizing is the same. There is a wide variation in quality and hardness even within a “type,” depending on the specific process, the ingredients of the electrolyte solution, and the length of time the aluminum is subjected to current. According to Orvis’s Jim Lepage, the vast majority of reels on the market feature anodizing in the low to mid-range of hardness for the type. The harder the coating the less shiny the finish the manufacturer can achieve through the polishing process. And no matter how sophisticated we think we are, market research proves that shiny sells.

4 thoughts on “Pro Tips: What Does “Anodized” Mean for a Fly Reel?

  1. GR

    Can you anodize die-cast reels, or just machined reels? And if you can, do die cast reels usually go through the anodization process? Or, is it just too expensive to be worthwhile, since most die-cast reels are targeted toward a certain price point?

    Just curious. Thanks.

    Reply
    1. Ian

      I worked in a foundry a few years ago they would anodized cast stuff after they heat treated it but I don’t know if they do that to all stuff cast

      Reply
  2. Henry

    The cast process is cheaper cost for manufacturer as it requires less machining and scrap, compared to a. Machined reel from round stock. When buying a casted reel you only paying for the aluminum that was poured.

    Reply
  3. andy

    Anodizing creates a slightly more durable surface than not anodizing. It certainly does not weather as quickly as raw aluminum. I think, in practice, the real reason for anodizing is because research proves that colorful sells, in addition to shiny!

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *